Jul

15

How to Properly Shampoo Carpet

It is, therefore, essential that carpets are shampooed to ensure that they remain clean and last for the expected time. Even though vacuuming regularly will help eliminate the top layer of dirt, it is always good to occasionally bring in carpet shampoo cleaners that help pull out the dirt, stains, oils, and allergens from deeper within the carpets. This is how one should shampoo his carpets, detailed step by step.

Assemble the Necessary Supplies

Before shampooing, assemble all the tools and products you’ll need:

– Liquid cleaner specially developed in portable encapsulation machines for carpet cleaning.

– Carpet cleaning machine for showering, which is used in shampooing carpets

– White cloths

– Rubber gloves

– Eye protection

Vacuum Thoroughly

The first process of carpet cleaning is to vacuum the whole area that needs to be shampooed with a vacuum cleaner with an adjustable beater bar brush. Do not forget the corners and areas behind furniture, such as couches and tables; always vacuum these areas. This helps lift the dirt on the surface so that it does not end up being ground back into the carpet during the shampooing process.

Pre-treat Any Stained Areas

Look for any stains that may be difficult to remove or areas that tend to get heavy traffic and are very dirty. Heavily traveled areas should be pre-sprayed with a carpet spot cleaner or traffic lane cleaner before shampooing. After washing apply on the affected area let it penetrate for about 5-10 minutes then wipe with white cloths. This is because it will enable the shampooing exercise to rinse off any other remaining stains in the area.

Fill the Machine Reservoir

The cleaning machine also has tank compartments that need to be emptied of any old water or cleaning solutions left from previous use. Run hot tap water into the solution tank, then pour carpet shampoo concentrate into the tank as indicated in the bottle. Tighten the caps on screw-type vials. It will help the cleaner to get to work and soften up soils so they can be broken down more easily by the hot water.

Shampoo the Carpets

Connect the carpet cleaning machine to the power supply and arrange the machine accordingly. Turning all the knobs down, set them on the positions that are suitable for shampooing carpets. The first step is to paint the area far from the doors and windows.

To clean the surface, apply pressure on the handle to activate the brushes and draw the device backward over three to four feet. Flat edges, fine lines, thin layers of paint, and smooth, continuous strokes that slightly overlap. Don’t rush through it. The brushes require some time to bring the dirt into the lower-end part of the carpet fibers.

Avoid Overwetting

This is an essential aspect since excessive wetting of the carpets is unlikely to be beneficial. Any remaining dirty water and soap residue needs to be harvested by going over each section with the suction only at a slow speed once again.

Ensure that any droppings of water are not seen on the ground. Another negative result of overwetting is that the carpet takes very long to dry, hence exposing it to the risk of developing mold and mildew.

Rinse and Repeat: This usually means that if the speaker feels the listener has not understood what was said, the process is repeated to ensure comprehension is achieved.

Before proceeding with the cleaning of the following one or two sections, inspect the waste tank. If it is full of dirty water, empty the container and fill it with clean water. After cleaning, check the areas you had first cleaned again. If they seem to require further rinse, prepare a new batch of the cleaning solution, but wash only the dirty areas.

Groom the Nap

After cleaning the carpet, groom the carpet surface with a specialized carpet groomer tool that will help to cut the pile and give the carpet a fresh appearance. This helps to reform the crushed fiber and also ensures that drying time is reduced. Ensure that the carpets are allowed to dry up to the maximum before individuals start walking on the floor or rearranging furniture. It is advisable to place the fans near the surface as this will enhance the rate of evaporation.

Here are some additional tips for effective carpet shampooing:

– Work in sections and allow carpets to dry for some time before proceeding to other sections that have not been treated.

– Take a few other windows in the same room or the next and open the fans to enhance the period of drying.

– Again, vacuum when carpets are through the process of drainage

– That is why it is important not to walk with shoes on damp carpets as it can easily re-soil them.

– Light colored carpets should be cleaned first then followed by the darker carpets to prevent cross contamination of dyes.

Conclusion

Carpets can be shampooed to remove the dirt that is left behind by the vacuuming process since it cleans deep into the carpets. These are the following instructions to assemble supplies and pre-treat stains, shampoo methodically step by step and give enough time for carpets to dry and having fresh smell. After consulting with the professionals, it is recommended to shampoo carpets every 6-12 months. There may be particular locations which would require frequent washing for optimum cleanliness to be achieved.